iPhone 13 Pro Max Screen Replacement
📦 Get Your Repair Kit First
You'll need these parts to fix your iPhone 13 Pro Max:
As an Amazon Associate we earn from qualifying purchases. This costs you nothing extra and helps keep this site free.
⚡ Protect Your Screen — Cheaper Than Repair
A quality case + screen protector is 5% the cost of one screen replacement.
Survives 6-foot concrete drops — saves you a $200+ screen bill
9H tempered glass — first line of defense against cracks
Microfiber + brush + alcohol wipes
64 bits, pro-grade — for serious DIY repair only
Replace your cracked iPhone 13 Pro Max display. The largest 13-series iPhone features a 6.7" Super Retina XDR display with ProMotion 120Hz refresh rate.
- Larger display = more careful handling required
- ProMotion (120Hz) requires quality OLED replacement
- Face ID MUST be transferred - extremely fragile
- True Tone requires Apple programming to restore
iPhone 13 Pro Max Display Specs
- Display: 6.7-inch Super Retina XDR OLED
- Resolution: 2778 x 1284 pixels, 458 ppi
- ProMotion: Adaptive 10Hz-120Hz refresh rate
- Features: HDR, True Tone, Wide color (P3)
- Brightness: 1000 nits typical, 1200 nits HDR
🛠️ Tools You'll Need
- Pentalobe P2 Screwdriver
- Tri-Point Y000 Screwdriver
- Phillips #000 Screwdriver
- Suction Cup
- Plastic Opening Picks (3+)
- Plastic Spudger
- Heat Gun or Hair Dryer
- Replacement Screen Assembly
As an Amazon Associate we earn from qualifying purchases.
📋 Difficulty & Time
🔧 Replace the Screen: Step by Step
Step 1: Power Off & Prepare Workspace
Power the iPhone off completely. Set up a clean, well-lit workspace on a non-static surface (a microfiber cloth on a desk works). Have screw organizers ready.
Step 2: Remove Bottom Pentalobe Screws
Two pentalobe P2 screws at the bottom edge, one on each side of the Lightning/USB-C port. Keep these in a labeled section — they're essential for water resistance.
Step 3: Apply Heat Around the Screen Edges
Use a heat gun (low setting) or hair dryer to warm the perimeter for 1–2 minutes per side. The display adhesive is strong — heat softens it.
Step 4: Create Initial Gap with Suction Cup
Apply suction cup to the bottom-center of the screen. Pull upward steadily while pressing down on the aluminum frame. Listen for the adhesive to release.
Step 5: Insert Picks — Bottom and LEFT Side Only
Slide thin plastic picks into the gap. Work along the bottom and LEFT side. The RIGHT side has display ribbon cables — DO NOT pry there or you'll damage them.
Step 6: Lift Screen Like a Book
Open the screen upward at 90°. The ribbon cables are still attached — do not pull harder.
Step 7: Disconnect the Battery FIRST
Remove the bracket over the battery connector (2–3 tri-point Y000 screws), then gently lift the connector with a spudger. This prevents short-circuits when you disconnect the screen.
Step 8: Disconnect the Display Ribbon Cables
Remove the bracket over the display connectors at the top. Carefully lift each ribbon cable with a plastic spudger. Note the order — there are usually 3 (front sensors, OLED panel, digitizer).
Step 9: Transfer Components from Old Screen
Front camera assembly, earpiece speaker, and (on Face ID phones) the True Depth camera have to move from the old screen to the new one. Failing to transfer the original IC chip = Face ID stops working forever.
Step 10: Install New Screen + Reconnect
Reverse: connect display ribbons → bracket → battery connector → bracket. Test BEFORE sealing — boot the device and verify touch + display work.
Step 11: Apply New Adhesive + Seal
Most replacement kits include adhesive strips. Apply along the perimeter, then close the screen by aligning the top hinge edge first, then pressing the bottom shut. Re-install pentalobe screws.
⚠️ Common Mistakes to Avoid
- Prying on the right side and tearing display ribbon cables (you've broken the new screen)
- Forgetting to disconnect the battery first (short-circuits the logic board)
- Not transferring the True Depth camera (kills Face ID permanently)
- Using too much heat (warps the OLED at temps over 150°F)
- Sealing without testing (have to redo everything if something doesn't work)
🏥 When to Call a Pro
If you damage a ribbon cable, snap a screw, or the new screen has dead pixels: stop. Apple charges $129–$429 depending on model. Third-party shops typically charge $179–$279 with a 90-day warranty. Mail-in services are available at iphoneipadfix.com/mail-in-repair.html.
Tools Required
- Pentalobe screwdriver (P2)
- Tri-point Y000 screwdriver
- Phillips #000 screwdriver
- Suction cup (larger helps)
- Plastic pry tools / spudger
- Tweezers
- Heat gun or iOpener
- Magnetic mat
- iPhone 13 Pro Max replacement screen
Pro Max Specific Tips
- More adhesive area - heat all edges thoroughly
- Display is heavier - support it well during repair
- Flex cables are in same positions as 13 Pro
- Battery is larger - same disconnection procedure
Replacement Process
The replacement process is identical to the iPhone 13 Pro, with the main difference being the larger display size:
- Power off and remove bottom pentalobe screws
- Heat edges (takes longer due to larger size)
- Open display from left side like a book
- Disconnect battery first
- Remove display cable brackets and disconnect
- Transfer Face ID/earpiece module to new screen
- Reconnect all cables in reverse order
- Test before sealing
- Apply new adhesive and close
Replacement Screen Quality
The larger 6.7" display makes quality differences more noticeable:
- OEM/Refurbished: Best quality, maintains all features
- High-quality OLED: Good color and brightness, may lack True Tone
- LCD replacement: NOT recommended - no ProMotion, worse blacks
Professional Repair Available
The iPhone 13 Pro Max is Apple's flagship - get it repaired right. Our technicians specialize in Pro Max repairs.
Get Pro Help →📦 Parts
Shop Parts on Amazon →🛒 Recommended Products
The #1 repair kit — 64 bits, pro tools, lifetime warranty
EZ Fit tray — foolproof install, 9H tempered glass 2-pack
Charge iPhone, Watch & AirPods — one compact cube