iPhone 12 Pro Screen Replacement
Replace your cracked iPhone 12 Pro display. The first iPhone with Ceramic Shield glass, though it can still crack. This guide covers the 6.1" Pro model.
As an Amazon Associate we earn from qualifying purchases. This costs you nothing extra and helps keep this site free.
⚡ Protect Your Screen — Cheaper Than Repair
A quality case + screen protector is 5% the cost of one screen replacement.
Survives 6-foot concrete drops — saves you a $200+ screen bill
9H tempered glass — first line of defense against cracks
Microfiber + brush + alcohol wipes
64 bits, pro-grade — for serious DIY repair only
- iPhone 12 Pro and iPhone 12 use DIFFERENT screens
- Face ID module must be carefully transferred
- LiDAR scanner is on the rear - not affected by screen repair
- Stainless steel frame is more scratch-prone during repair
iPhone 12 Pro Display Specs
- Display: 6.1-inch Super Retina XDR OLED
- Resolution: 2532 x 1170 pixels, 460 ppi
- Refresh rate: 60Hz
- Protection: Ceramic Shield front
- Features: HDR, True Tone, Wide color (P3)
- Brightness: 800 nits typical, 1200 nits HDR
🛠️ Tools You'll Need
- Pentalobe P2 Screwdriver
- Tri-Point Y000 Screwdriver
- Phillips #000 Screwdriver
- Suction Cup
- Plastic Opening Picks (3+)
- Plastic Spudger
- Heat Gun or Hair Dryer
- Replacement Screen Assembly
As an Amazon Associate we earn from qualifying purchases.
📋 Difficulty & Time
🔧 Replace the Screen: Step by Step
Step 1: Power Off & Prepare Workspace
Power the iPhone off completely. Set up a clean, well-lit workspace on a non-static surface (a microfiber cloth on a desk works). Have screw organizers ready.
Step 2: Remove Bottom Pentalobe Screws
Two pentalobe P2 screws at the bottom edge, one on each side of the Lightning/USB-C port. Keep these in a labeled section — they're essential for water resistance.
Step 3: Apply Heat Around the Screen Edges
Use a heat gun (low setting) or hair dryer to warm the perimeter for 1–2 minutes per side. The display adhesive is strong — heat softens it.
Step 4: Create Initial Gap with Suction Cup
Apply suction cup to the bottom-center of the screen. Pull upward steadily while pressing down on the aluminum frame. Listen for the adhesive to release.
Step 5: Insert Picks — Bottom and LEFT Side Only
Slide thin plastic picks into the gap. Work along the bottom and LEFT side. The RIGHT side has display ribbon cables — DO NOT pry there or you'll damage them.
Step 6: Lift Screen Like a Book
Open the screen upward at 90°. The ribbon cables are still attached — do not pull harder.
Step 7: Disconnect the Battery FIRST
Remove the bracket over the battery connector (2–3 tri-point Y000 screws), then gently lift the connector with a spudger. This prevents short-circuits when you disconnect the screen.
Step 8: Disconnect the Display Ribbon Cables
Remove the bracket over the display connectors at the top. Carefully lift each ribbon cable with a plastic spudger. Note the order — there are usually 3 (front sensors, OLED panel, digitizer).
Step 9: Transfer Components from Old Screen
Front camera assembly, earpiece speaker, and (on Face ID phones) the True Depth camera have to move from the old screen to the new one. Failing to transfer the original IC chip = Face ID stops working forever.
Step 10: Install New Screen + Reconnect
Reverse: connect display ribbons → bracket → battery connector → bracket. Test BEFORE sealing — boot the device and verify touch + display work.
Step 11: Apply New Adhesive + Seal
Most replacement kits include adhesive strips. Apply along the perimeter, then close the screen by aligning the top hinge edge first, then pressing the bottom shut. Re-install pentalobe screws.
⚠️ Common Mistakes to Avoid
- Prying on the right side and tearing display ribbon cables (you've broken the new screen)
- Forgetting to disconnect the battery first (short-circuits the logic board)
- Not transferring the True Depth camera (kills Face ID permanently)
- Using too much heat (warps the OLED at temps over 150°F)
- Sealing without testing (have to redo everything if something doesn't work)
🏥 When to Call a Pro
If you damage a ribbon cable, snap a screw, or the new screen has dead pixels: stop. Apple charges $129–$429 depending on model. Third-party shops typically charge $179–$279 with a 90-day warranty. Mail-in services are available at iphoneipadfix.com/mail-in-repair.html.
12 Pro vs 12 Differences
Key hardware differences:
- Stainless steel frame vs aluminum (Pro is heavier)
- Different screen flex cable connector positions
- Screens are NOT interchangeable between 12 and 12 Pro
- Triple camera vs dual camera (rear)
Tools Required
- Pentalobe screwdriver (P2)
- Tri-point Y000 screwdriver
- Phillips #000 screwdriver
- Suction cup
- Plastic pry tools / spudger
- Tweezers
- Heat gun or iOpener
- Magnetic mat
- iPhone 12 Pro replacement screen
Replacement Steps
- Power off the iPhone completely
- Remove the two pentalobe screws at the bottom
- Heat edges to soften adhesive
- Apply suction cup and gently pry open
- Open display from left side like a book
- Disconnect battery before any other work
- Remove display cable bracket screws
- Disconnect display flex cables
- Transfer Face ID/earpiece module to new screen
- Reassemble in reverse order
- Test before sealing (Face ID, touch, display)
Protecting the Steel Frame
- Use plastic tools only - avoid metal
- Consider masking tape on frame edges
- Work on a soft, clean surface
Need Expert Help?
iPhone 12 Pro screen replacement requires precision. Our technicians can do it right.
Get Pro Help →📦 Parts
Shop Parts on Amazon →🛒 Recommended Products
The #1 repair kit — 64 bits, pro tools, lifetime warranty
EZ Fit tray — foolproof install, 9H tempered glass 2-pack
Charge iPhone, Watch & AirPods — one compact cube