iPhone 11 Pro Screen Replacement
Replace your cracked iPhone 11 Pro display. The Pro model features a premium OLED display unlike the standard iPhone 11's LCD.
As an Amazon Associate we earn from qualifying purchases. This costs you nothing extra and helps keep this site free.
⚡ Protect Your Screen — Cheaper Than Repair
A quality case + screen protector is 5% the cost of one screen replacement.
Survives 6-foot concrete drops — saves you a $200+ screen bill
9H tempered glass — first line of defense against cracks
Microfiber + brush + alcohol wipes
64 bits, pro-grade — for serious DIY repair only
iPhone 11 Pro Display Specs
- Display: 5.8-inch Super Retina XDR OLED
- Resolution: 2436 x 1125 pixels, 458 ppi
- Features: HDR, True Tone, Wide color (P3)
- Brightness: 800 nits typical, 1200 nits HDR
- Frame: Stainless steel
🛠️ Tools You'll Need
- Pentalobe P2 Screwdriver
- Tri-Point Y000 Screwdriver
- Phillips #000 Screwdriver
- Suction Cup
- Plastic Opening Picks (3+)
- Plastic Spudger
- Heat Gun or Hair Dryer
- Replacement Screen Assembly
As an Amazon Associate we earn from qualifying purchases.
📋 Difficulty & Time
🔧 Replace the Screen: Step by Step
Step 1: Power Off & Prepare Workspace
Power the iPhone off completely. Set up a clean, well-lit workspace on a non-static surface (a microfiber cloth on a desk works). Have screw organizers ready.
Step 2: Remove Bottom Pentalobe Screws
Two pentalobe P2 screws at the bottom edge, one on each side of the Lightning/USB-C port. Keep these in a labeled section — they're essential for water resistance.
Step 3: Apply Heat Around the Screen Edges
Use a heat gun (low setting) or hair dryer to warm the perimeter for 1–2 minutes per side. The display adhesive is strong — heat softens it.
Step 4: Create Initial Gap with Suction Cup
Apply suction cup to the bottom-center of the screen. Pull upward steadily while pressing down on the aluminum frame. Listen for the adhesive to release.
Step 5: Insert Picks — Bottom and LEFT Side Only
Slide thin plastic picks into the gap. Work along the bottom and LEFT side. The RIGHT side has display ribbon cables — DO NOT pry there or you'll damage them.
Step 6: Lift Screen Like a Book
Open the screen upward at 90°. The ribbon cables are still attached — do not pull harder.
Step 7: Disconnect the Battery FIRST
Remove the bracket over the battery connector (2–3 tri-point Y000 screws), then gently lift the connector with a spudger. This prevents short-circuits when you disconnect the screen.
Step 8: Disconnect the Display Ribbon Cables
Remove the bracket over the display connectors at the top. Carefully lift each ribbon cable with a plastic spudger. Note the order — there are usually 3 (front sensors, OLED panel, digitizer).
Step 9: Transfer Components from Old Screen
Front camera assembly, earpiece speaker, and (on Face ID phones) the True Depth camera have to move from the old screen to the new one. Failing to transfer the original IC chip = Face ID stops working forever.
Step 10: Install New Screen + Reconnect
Reverse: connect display ribbons → bracket → battery connector → bracket. Test BEFORE sealing — boot the device and verify touch + display work.
Step 11: Apply New Adhesive + Seal
Most replacement kits include adhesive strips. Apply along the perimeter, then close the screen by aligning the top hinge edge first, then pressing the bottom shut. Re-install pentalobe screws.
⚠️ Common Mistakes to Avoid
- Prying on the right side and tearing display ribbon cables (you've broken the new screen)
- Forgetting to disconnect the battery first (short-circuits the logic board)
- Not transferring the True Depth camera (kills Face ID permanently)
- Using too much heat (warps the OLED at temps over 150°F)
- Sealing without testing (have to redo everything if something doesn't work)
🏥 When to Call a Pro
If you damage a ribbon cable, snap a screw, or the new screen has dead pixels: stop. Apple charges $129–$429 depending on model. Third-party shops typically charge $179–$279 with a 90-day warranty. Mail-in services are available at iphoneipadfix.com/mail-in-repair.html.
- iPhone 11 Pro uses OLED - better colors, true blacks
- Standard iPhone 11 uses LCD
- Screens are NOT interchangeable
- OLED replacements cost more but look better
Tools Required
- Pentalobe screwdriver (P2)
- Tri-point Y000 screwdriver
- Phillips #000 screwdriver
- Suction cup
- Plastic pry tools / spudger
- Tweezers
- Heat gun or iOpener
- Magnetic mat
- iPhone 11 Pro OLED replacement screen
Replacement Process
- Power off the iPhone
- Remove two pentalobe screws at bottom
- Heat edges to soften adhesive
- Use suction cup to open from right side
- iPhone 11 Pro opens from RIGHT (different from newer models)
- Disconnect battery first
- Remove display brackets and disconnect cables
- Transfer Face ID/earpiece components
- Install new display and reconnect
- Test thoroughly before sealing
Choosing a Replacement Screen
- OEM/Refurbished OLED: Best quality, maintains all features
- Aftermarket OLED: Good quality, slightly lower brightness
- LCD replacements: Cheaper but loses true blacks and HDR
Get Professional Service
iPhone 11 Pro OLED screens require careful handling. Our technicians can ensure a quality repair.
Get Pro Help →📦 Parts
Shop Parts on Amazon →🛒 Recommended Products
The #1 repair kit — 64 bits, pro tools, lifetime warranty
EZ Fit tray — foolproof install, 9H tempered glass 2-pack
Charge iPhone, Watch & AirPods — one compact cube